Why Learning Plumbing Basics is Vital for Bathtub Installation
Why Learning Plumbing Basics is Vital for Bathtub Installation
Blog Article
The article author is making a number of good pointers about How to Install a Bathtub Yourself in general in this article on the next paragraphs.
Mounting a tub isn't specifically brain surgery, however it does need solid plumbing, carpentry, as well as occasionally, tiling abilities. Changing an old bath tub with a new one is also a reasonably challenging job. If the old tub is readily easily accessible, the project can move rapidly; if you need to open up a wall surface to get rid of the old tub and also place the new bathtub, the job is much harder. In either instance, the project is within a residence handyman's skills, although you will require a helper to move out the old tub and embeded in the brand-new one. Make sure you have actually certified on your own for the task and are comfortable trying it. Instead of hiring a specialist to take control of a halfway-completed task, it is much better to take into consideration utilizing one prior to you start. Chances are you might need a specialist plumber to make tube links.
This write-up will certainly assist you install a brand-new bathtub in your bathroom if you have actually already purchased a brand-new tub as well as don't need to transform the plan of your previous water system pipes.
Your devices and also material checklist need to consist of the following:
Getting ready for the Setup
To start with, the supporting framework supplied with the bathroom must be fitted (if required) according to the maker's directions. Next, fit the faucets or mixer to the tub. When fitting the tap block, it is essential to make sure that if the tap comes with a plastic washer, it is fitted between the bathroom as well as the taps. On a plastic bathroom, it is additionally sensible to fit a supporting plate under the faucets device to prevent stress on the bath tub.
Fit the adaptable faucet connectors to the bottom of both taps making use of 2 nuts and also olives (occasionally supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the outlet via the hole in the bath. Utilize the nut provided by the producer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bathroom. Make certain you utilize every one of the supplied washing machines.
Connect the trap to the bottom of the waste outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom should now be ready to be fitted in its last position.
Removing Old Touches
If you need to replace old faucets with brand-new ones as a part of your installment, then the first thing you need to do is detach the water system. After doing so, turn on the faucets to drain any water staying in the system. The process of getting rid of the existing faucets can be fairly problematic due to the limited gain access to that is frequently the situation.
Make use of a container wrench (crowsfoot spanner) or a tap device to reverse the nut that attaches the supply pipes to the faucets. Have a towel all set for the staying water that will certainly come from the pipes. When the supply pipelines have been gotten rid of, utilize the very same device to loosen up the nut that holds the taps onto the bath/basin. You will require to stop the solitary taps from transforming throughout this process. Once the faucets have actually been gotten rid of, the holes in the bath/basin will have to be cleaned up of any old securing compound.
Prior to carrying on to fit the new taps, compare the pipe connections on the old faucets to the brand-new faucets. If the old taps are longer than the brand-new faucets, then a shank adapter is needed for the brand-new taps to fit.
Setting up the Tub
Using the two wooden boards under its feet, position the tub in the needed position. The wooden boards are helpful in evenly spreading out the weight of the bath tub over the area of the boards as opposed to focusing all the weight onto four little points.
The next objective is to make certain that the bath tub is leveled all round. This can be attained by examining the level as well as readjusting the feet on the bathtub until the level checks out degree.
To mount faucets, fit the bottom of the furthest adaptable tap connector to the ideal supply pipeline by making a compression sign up with; after that do the very same for the various other tap.
Switch on the water supply and also inspect all joints and also new pipework for leakages as well as tighten them if required. Load the bathtub and additionally examine the overflow outlet and the regular outlet for leakages.
Ultimately, repair the bath paneling as described in the manufacturer's user's manual. Tiling and sealing around the bathtub ought to wait up until the bathtub has actually been utilized a minimum of when as this will resolve it into its final position.
Fitting New Touches
If the tails of the new faucets are plastic, after that you will certainly require a plastic port to prevent damages to the string. One end of the port fits on the plastic tail of the faucet and the various other end offers a connection to the current supply pipelines.
If you require to fit a monobloc, then you will need decreasing couplers, which connects the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next off, place the tap in the installing hole in the bath/basin making sure that the washers are in area between the faucet as well as the sink. Protect the tap in place with the supplier offered backnut. Once the faucet is safely in place, the supply pipes can be linked to the tails of the taps. The taps can either be connected by using corrugated copper piping or with regular faucet connectors. The former type needs to be linked to the faucet finishes first, tightening up just by hand. The supply pipes can later be connected to the various other end. Tighten up both ends with a spanner after both ends have actually been connected.
Tiling Around the Bath tub
In the area where the bathroom meets the ceramic tile, it is required to secure the joins with a silicone rubber caulking. This is important as the fitting can relocate enough to split a stiff seal, creating the water to permeate the wall surface in between the bath as well as the tiling, causing issues with wetness and also possible leakages to the ceiling listed below.
You can choose from a selection of coloured sealants to blend in your components as well as fittings. They are offered in tubes as well as cartridges, and are capable of securing gaps as much as a size of 3mm (1/8 inch). If you have a larger gap to load, you can fill it with twists of drenched newspaper or soft rope. Bear in mind to constantly fill the tub with water prior to sealing, to allow for the movement experienced when the tub is in use. The sealant can break fairly early if you do not take into account this motion prior to securing.
Additionally, ceramic coving or quadrant tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are additionally easily offered on the market. It is suggested to fit the ceramic tiles utilizing waterproof or water-proof sticky and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We hope you enjoyed reading our excerpt about How to Install a Bathtub. Thank you so much for finding the time to read through our posting. Enjoyed reading our write-up? Please share it. Help others discover it. Thanks for your time spent reading it.
Overflow issues? Our professionals await. Report this page